Home > Products > Tube Furnace
1600℃ Horizontal Flash Sintering Furnace with 3KW Programmable Power Source1600℃ Horizontal Flash Sintering Furnace with 3KW Programmable Power Source1600℃ Horizontal Flash Sintering Furnace with 3KW Programmable Power Source

1600℃ Horizontal Flash Sintering Furnace with 3KW Programmable Power Source

    CY-T1600-80IT-FS is a horizontal tube furnace with 3KW programmable AC power source designed for exploring the flash-sintering for ceramic materials at a lower cost.The tube furnace comes with 80mm OD alumina tube and a sliding sample fixture, which can preheat sample up to 1600℃.

CY-T1600-80IT-FS is a horizontal tube furnace with 3KW programmable AC power source designed for exploring the flash- sintering for ceramic materials at a lower cost.The tube furnace comes with 80mm OD alumina tube and a sliding sample fixture, which can preheat sample up to 1600℃. The Sample holder will press electric wire to the sample via ceramic screw to pass through programmable AC power source which is programmable up to 1500W power.

Flash-sintering is an new technology which is used widely in the research of solid state electrolyte, SOFC and fero-magnetic & Thermo-electric materials.

Technical parameters:

Tube Furnace

208 - 240 VAC, 50/60Hz, 5.2 KW max. power consumption

Working temperature: 1600℃ continuous and 1700 Max.

Heating Zone length: 18" ( 457 mm )

Constant temperature zone: 6"  (150 mm) within +/- 1

Temperature Control

PID automatic control via solid state relay with 30 steps programmable and  +/-1 accuracy

Built-in Over Temperature and Thermocouple Failure Protection

B-type thermal couple

Vacuum Sealing Flanges

& Sample Fixture

Vacuum Flanges are made of stainless steel which can reach the vacuum to 10-2 torr by mechanical pump and 10-5 torr by turbo pump.
  Left Side Flange:

30 mm dia. Quartz observation window

 Needle valve with 1/4 NSP connector

Right Side Flange:

KF25 vacuum port to connect to a vacuum pump

Two electric wires feedthrough. Wires are made of Platinium with 1 mm diameter

Needle valve with mechanical vacuum gauge.

Sample fixture is built-in the inside flange.

This flange is slidable to make sample loading easy.

Programmable AC Power Source

The programmable AC power source is to connect the electric wire at the feedthrough at the right side flange. After pre-heating, AC power will pass a sample as programa setting to produce more heat rapindly, which results in sample sintered in high density. The power parameters can be set via included abtop. Power source specifications ae as the below

Input Voltage: AC220V±10%, 50/60Hz, single phase

Power Capacity: 3000 W Max.

Circuit Type: IGBT, PWM

Output Voltage: 50V-300V adjustable with ≤1% stability

Output Frequency: 50/60Hz fixed with ≤0.01% stability

Protection: Overload, over temperature, and short circus

PC programmable: Laptop with pre-installed software is included for program setting

Optional: DC power source 400V/10A is available upon request at the extra cost

Dimensions & Weight

1950L×500 W ×720 H, mm

150Kg

Warranty

One year limited warranty with lifetime support (Consumable parts such as tubes and o-rings are not covered by the warranty)


Disclaimer: The product introduction content (including product images, product descriptions, technical parameters, etc.) of this site is for reference only. As the update may not be timely, there will be some differences between the content and the actual situation. Please contact our sales staff to confirm. The information provided on this site does not constitute any offer or promise, and the company will periodically improve and modify the website information, without prior notice, please understand.

Contact Us
  • E-mail: cysi@cysi.wang
  • Tel: +86 371 5519 9322
  • Fax: +86 371 8603 6875
  • Add: No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China




Follow Us

Copyright © Zhengzhou CY Scientific Instrument Co., Ltd. All Rights Reserved    Update cookies preferences

| Sitemap |       Technical Support: